HP Integrity Superdome 2 BLADE DEGRADED等报错

产品

	AIX COMMAND,AIX 常用命令与操作。。。。技术服务;

	powervm 环境vscsi映射的盘missing 链路正常？

	Aix 安装openssh启动ssh服务启不启来

	HACMP模式下替换旧存储硬盘

	ibm Power5 9110-51A (p5 510) 液晶屏显示。。。。技术服务;

	ibm Power5 9111-520 (p5 520) 液晶屏显示。。。。技术服务;

	ibm Power5 9131-52A (p5 52A) 液晶屏显示。。。。技术服务;

	ibm Power5 9113-550 (p5 550) 液晶屏显示。。。。技术服务;

	ibm Power5 9133-55A (p5 55A) 液晶屏显示。。。。技术服务;

	ibm Power5 9116-561 (p5 560Q) 液晶屏显示。。。。技术服务;

	ibm Power5 9117-570 (p5 570) 液晶屏显示。。。。技术服务;

	ibm Power5 9118-575 (p5 575) 液晶屏显示。。。。技术服务;

	ibm Power5 9119-590 (p5 590) 液晶屏显示。。。。技术服务;

	ibm Power5 9119-595 (p5 595) 液晶屏显示。。。。技术服务;

	HMC 无法连接主机

	HMC 无法Add(添加）主机

	HMC 无法Ping通主机IP地址

	HMC LPAR/逻辑分区 = 空

	HMC 恢复逻辑分区/LPAR RECOVERY

	联系电话/Tel:

	Moble: 13301272832 (微信同号)


	Tel: 　010-82666745

	联系人：　霍经理

	QQ: 　　619804118

	E-mail: 　　bjslkc@163.com

	公司：北京深蓝融鑫科技发展有限公司

HP Integrity Superdome 2 Servers - SD2/HP-UX: Blade status Showing as Degraded (BLADE_DEGRADED) Due to Unexpected Reset/Failure by Processor Dependent Hardware Controller (PDHC) with Event Code PDHC_UNEXPECTED_REBOOT

Issue

Blade status showing Degraded due to Processor Dependent Hardware Controller (PDHC) has unexpectedly reset/ failed. System was up and running and there were no MCA's

SHOW COMPLEX STATUS - Enclosure

Device Degraded Failed

Current Wattage used: 1100

Health: Failed

Unit Identification LED: Off

Virtual Fan: 55%

Diagnostic Status:

Internal Data OK

Management Processor OK

Sl.No Severity EventId EventCategory PartitionId EventTime Summary

SHOW CAE -E -n 368

Summary :

Processor Dependent Hardware Controller reset

Full Description :

The Processor Dependent Hardware Controller (PDHC) has unexpectedly reset. The system has recovered from the problem

Probable Cause 1 :

A hardware problem prevented forward progress

Recommended Action 1:

Check for other fault messages.

Probable Cause 2:

A firmware problem prevented forward progress.

Recommended Action 2:

Verify that the most recent firmware is installed on the system.

SHOW CAE -E -n 366

Summary :

Failed to access a FPGA component

Full Description :

Failed to access a FPGA component

Probable Cause 1:

CEC component or hardware failure

Recommended Action 1:

Verify the current supported firmware version is installed. Replace the blade.

中国·北京联系方式：

1）联系人：　霍经理
2）手　机：　13301272832 (微信同号)
3）QQ: 619804118
4）联系电话：（010）82666745
5）传　　真：（010）82666745
6）E-mail: 　　bjslkc@163.com
7）公司：北京深蓝融鑫科技发展有限公司
8）地址：北京市海淀区西北旺
9）公司地址、乘车路线及公司位置地图